We offer finest polycarbonate sheet in market

Services & Warranty

WARRANTY AGAINST HAILSTONE BREAKAGE :

If during a three (3) year period from the date of sale this product suffers hail breakage (defined as surface penetration or puncture that permits water to leak through) from hailstones measuring up to 7/8 inch (22.2 mm) traveling at speeds up to 60 meters/second, VIBRANT  SAPPHIRE will provide a replacement sheet to the purchaser thereof, or fabricator designated by the purchaser, at a cost to the purchaser of 1/36 of the original purchase price for each month from date of sale. The failed sheet, original sales receipt and this warranty must be returned to  VIBRANT SAPPHIRE or to the original dealer. If a replacement sheet cannot be provided within fourteen days, VIBRANT SAPPHIRE may opt to refund the pro-rated purchase price of the original sheet. 

CONDITIONS :

This warranty applies only to sheet fabricated, installed, and cleaned according to ULTRA SAPPHIRE  recommendations as stated publications produced by  VIBRANT SAPPHIRE products. It is important to note sheet is designed for weathering resistance and does NOT PROVIDE ABRASION RESISTANCE; NO WARRANTIES ARE EXTENDED ON THE ABRASION RESISTANCE CHARACTERISTICS OF THIS PRODUCT. THIS WARRANTY DOES NOT COVER (RE)INSTALLATION EXPENSES OR ANY OTHER DIRECT OR INDIRECT LOSS(ES) WHICH MAY RESULT FROM THE SHEET FAILURE. Yellowing and Light Transmission: This warranty against yellowing and light transmission applies only to clear Polycarbonate sheets. The Yellowness Index (YI) of clear sheet cleaned according to the recommendations of Sapphire shall be less than 8.0 during a five-year period from the date of sale, and shall be less than 10 during a ten-year period from the date of sale as determined according to ASTM D1925 (1970). The light transmission characteristics of clear sheet, cleaned according to the recommendations of  VIBRANT SAPPHIRE shall not decrease by more than 12% during a ten-year period from the date of sale when tested by the procedure specified in ASTM D1003.

This warranty is limited to excessive yellowing and light transmission losses due to the degradation of Sapphire SHEET AND DOES NOT COVER YELLOWING OR LIGHT TRANSMISSION LOSSES DUE TO DIRT, ATMOSPHERIC DEPOSITS, ABRASION, OR CHANGES IN THE PHYSICAL STRUCTURE OF THE VIBRANT SAPPHIRE  SHEET. Impact: For a period of 3 years, this product shall be warranted against hail breakage (hail breakage defined as skin penetration) from hailstones up to 7/8" (22.2 mm) traveling at speeds up to 200 ft/sec (60 meters/sec). Resolution of claims will be determined through subsequent impact testing of the sheet in question using ASTM D3029/Ford Modified Gardner Test. A 7/8" hailstone travelling at 200 ft/sec equates to 5 ft-lbs force on the above test. Sheets testing less than 5 ft-lbs shall be warranted.

You should be aware that all glazing is subject to irreversible depositions of atmospheric elements and can be expected to show signs of hazing eventually.

Annual cleaning following recommended procedures will significantly reduce, but not eliminate, that process. (See reverse side for cleaning and maintenance instructions.) This warranty does not cover abrasion or scratching. THE WARRANTIES STATED IN THIS PUBLICATION ARE IN LIEU OF ALL OTHER WARRANTIES (EXCEPT OF TITLE), WRITTEN OR ORAL, STATUTORY, EXPRESS OR IMPLIED INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. GENERAL ELECTRIC'S SOLE OBLIGATION, WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL BE LIMITED TO REPLACING THE SHEET OR REFUNDING THE PRO-RATED ORIGINAL PURCHASE PRICE, AT ITS OPTION, WHICH SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY. GE STRUCTURED PRODUCTS SHALL IN NO EVENT BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, OR SPECIAL DAMAGES. UNDER NO CIRCUMSTANCES SHALL GENERAL ELECTRIC BE LIABLE FOR ANY AMOUNT GREATER THAN THE PURCHASE PRICE OF THE SHEET PURCHASED.

Notice: This dealer is authorized to fulfill the above obligations of this warranty to the purchaser.

This limited warranty must be completed by the dealer at the time of sale. 

PDM Sourcings–  VIBRANT SAPPHIRE Polycarbonate Sheets

CLEANING AND MAINTENANCE INSTRUCTIONS

Annual cleanings using proper procedures and compatible cleaners is recommended to prolong the service life. For general cleaning, it is recommended that the following instructions and cleaning agents be used. These procedures and cleaners are also recommended for use on the untreated, interior surface of the clear PDM /  VIBRANT  SAPPHIRE  sheet.

CLEANING PROCEDURES

• Rinse sheet with lukewarm water.

• Wash sheet with a mild soap and lukewarm water.

• Use a soft cloth or sponge and gently wash to loosen remaining dirt and grime. DO NOT SCRUB, USE BRUSHES OR ABRASIVE CLEANERS: the coating on sheet is UV resistant. It is NOT a Mar-Resistant Coating.

• Repeat rinse and dry with a soft cloth to prevent water spotting.

COMPATIBLE CLEANING AGENTS

• Aqueous Solutions of Soaps and Detergents Windex1 Top Job2 Joy2 Mr. Clean2 Fantastik3 Formula 4094

• Organic Solvents & Cleaners Aliphatic Hydrocarbons Neleco-Placer Kerosene Naptha (VM&P grade) Hexcel, F.O. 554 Turco 5042

• Alcohols Methanol Isopropyl

CAUTIONS

• Do not use abrasive or highly alkaline cleaners. Never scrape with razor blades or other sharp instruments.

• Benzene, leaded gasoline, acetone or carbon tetrachloride should never be used.

• Do not clean in hot sun or at elevated temperatures.

FRESH PAINT SPLASHES, GREASE AND GLAZING COMPOUND REMOVAL

Before drying, these conditions can be easily remedied by rubbing lightly with a good grade of VM&P naphtha, isopropyl alcohol, or butyl cellosolve. Afterwards, a warm final wash should be made using a mild soap or detergent solution and a thorough rinsing with clean water.

LABEL AND STICKER REMOVAL

The use of kerosene or VM&P naphtha are generally effective in removing labels and stickers. A warm wash and rinse should always follow the use of these products.

In cases where the sticker material, such as vinyl, does not allow the penetration of solvent, the application of heat (a hair dryer, for example) will soften the adhesive and promote removal.

Caution: Excessive heat can cause surface damage.

PDM sheet / VIBRANT  SAPPHIRE is coextruded on one side. The coextruded side must be glazed outwards or towards the light source to provide protection for the PDM sheet substrate. 

PDM Roffing sheets Warehouses 

OPP- Karala Dispensary , Karala Chowk , Karala Village - Delhi-110081

INDIA



Although all information, recommendations, or advice contained herein is given in good faith, no guarantee is made that the same results as those described will be obtained or, as to the effectiveness or safety of any design, and  VIBRANT  SAPPHIRE its subsidiaries, affiliates and authorized representatives shall in no event be held responsible for any loss incurred through such use of the products. Each user shall make its own determination of the suitability of the products or any such information, recommendations or advice for its own particular use. The products of VIBRANT  SAPPHIRE  , its subsidiaries or affiliates are sold in any event subject to the Conditions of Sale constituting part of the applicable representative or other sales agreement or printed on the back of order acknowledgments or invoices or are available upon request. Nothing in this or any other document or any oral recommendation or advice shall be deemed to alter, vary, supersede, or waive any of the Conditions of Sale. Statements concerning possible or suggested uses of the materials or designs described herein are not to be construed as constituting a license under any General Electric Company or subsidiary or affiliate company patent covering such use or as recommendations for use of such materials or designs in the infringement of any patent.